KG ELS-304 Скачать руководство пользователя страница 23

Страница: 23 / 80

ELS-304

Name and Function of Each Part

3-1

3. Name and Function of Each Part

Name and the functions of each part are described.

3.1

Front Panel

(1) Display

A 128x64 dot monochrome LCD panel. It displays setting and meas. values etc.

(2) Operation Panel

This panel consists of function keys, a rotary knob to change values, and ten keys to
input values. For specific operations, refer to

→

“

4.,5.,6.

”.

(3) Load terminal block

This the Terminal Block for the Load input. The max rated is 30V-120A-300W.

(4) Air inlet

To take air for cooling

Do not put an obstacle to block the airflow.

(5) Current monitor output

This is a volt. Output terminal so that you can monitor the load current of this product.
The signal is based on 10V/120A ratio. Refer to

→

“

2.3

CURRENT MONITER

”.

・

Current monitor output is NOT Isolated.

(4)

(3)

(5)

(6)

(7)

(1)

(2)

WARNING

Содержание ELS-304

















































































Результаты поиска

Содержание ELS-304

Отзывы:

Бренды по названию

Популярные бренды

KG ELS-304, Руководство по эксплуатации

Результаты поиска

Содержание ELS-304

Отзывы:

Бренды по названию

Популярные бренды