KG ELS-304 Скачать руководство пользователя страница 18

Страница: 18 / 80

ELS-304

2-4

Connections

WARNING

・

In case of reverse connection, this product alarms due to internal short condition.
But this product may be damaged if the current caused by the short exceeds
max. rated curr. (120A).

・

When you connect to a target device, never fail to power OFF the target device.

・

Do NOT apply any Volt other than the range (0-30V) any voltage outside this
range would damage this product.

(3) Ext. Control Cable

As for the cable between this product and use a shielded , twisted , or coaxial cable.

Both DC and AC can be inputted, but when you input AC, add the offset Volt. so that

the Volt should not be less than 0V always. The input of product should be in the
range between 0 and 10V, and DC and 500KHz (3dB).

・

Do NOT apply any Volt other than the range (0-10V) Any voltage outside this
range would damage this product.

Содержание ELS-304

















































































Результаты поиска

Содержание ELS-304

Отзывы:

Бренды по названию

Популярные бренды

KG ELS-304, Руководство по эксплуатации

Результаты поиска

Содержание ELS-304

Отзывы:

Бренды по названию

Популярные бренды