manualshive.com logo in svg

KG ELS-304, Руководство по эксплуатации

Поделиться
Скачать
KG ELS-304 Скачать руководство пользователя страница 13

ELS-304

 
 

Product outline

 

1-1 

 

1. Outline   

 

 

 

1.1

 

Outline

 

 

 
This product, ELS-304, has realized as fast as 200A/usec fast load response speed, slew 

rate that any other products have never realized so far due to our unique new type of load 

circuit. Ideal noiseless rising and falling waveforms that could not be achieved by any 
prior art such as simple semiconductor switches have been realized in this ELS-304. 

ELS-304 is a new generation high performance electronic load that can be used in 

applications where very high-speed load response is necessary such as in evaluation of 
characteristics of VRM/POL types of DC-DC converters.     

 

 

 

1.2

 

Features

 

 

 

・ 

Easy to connect, because the Load Terminal is located on the Front Panel. 

・ 

Very fast load response up to 200

Ａ

/

μ

s.(5V or more should be presented at the load 

terminal) 

・ 

Stable frequency response within 3dB up to 500KHz. (Ext.  AC offset Volt) 

・ 

No min. operating volt. Any volt difference drives the operation of this product. 

・ 

Worldwide power input. (100V-240V

 

50/60Hz) 

・ 

Various load modes like CC, CR, CV, CP, Dynamic, Ext. control, Short are supported. 

・ 

In the dynamic load mode, single and auto modes are supported. 

・ 

As the interface, both USB and GPIB are supported as the standard.   
By simply connecting to your PC via a USB cable, you can control this product to 
measure automatically.   

Via GP-IB, you can easily integrate this product to your existent system.   

・ 

Abundant Alarm Functions of Over Volt., Over Power, Reverse Connection, and Over 
Heat..    

・ 

By internal Curr. Limit function,    “ CV+Climit (Curr. Limit)” operation is supported. 

・ 

Five (5) digits Current. And Voltage, measurement.   

・ 

Up to 6 Meas./Setup Conditions Memory Function.   

・ 

Ripple Noise digital measurement function (factory option)   

Ripple noise can be measured by way of our unique method capable of measuring in 
digital eradicating human reading error in using an analog.   

 
 

 

 

   

In fast load response of 200

Ａ

/

μ

S, there are several cautions about the connection method 

and load volt. To be noted. 

   

For more information, Refer to 

→“

 2 Connections 

”

 

 
 

 

 
 

 

 
 

 

 
 

 
 

Supplement

Содержание ELS-304

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды