KG ELS-304 Скачать руководство пользователя страница 5

Страница: 5 / 80

ELS-304

For your safety use of this Product

III

Move

Before you move this product, turn off the power , and remove all

the cables from this product.

When you move this product , attach this manual to the product,

and use the dedicated or more robust packing material.

Maintenance

Before you do maintenance or check this product, make sure

than the Power Plug is detached.

To keep the safety of this product, periodical maintenance and

check would be suggested.

We would also suggest the periodical calibration to keep the

performance of this product

Overload

Do not use the connector of this product for any purpose that is

not described in this manual.

Do not apply Volt. that exceeds the specifications.

Repair / Adjustment

The Adjustment and Calibration can be done by Keisoku Giken.

Contacts or our distributor.

Содержание ELS-304

















































































Результаты поиска

Содержание ELS-304

Отзывы:

Бренды по названию

Популярные бренды

KG ELS-304, Руководство по эксплуатации

Результаты поиска

Содержание ELS-304

Отзывы:

Бренды по названию

Популярные бренды