KEPCO BHK-MG Series, Руководство оператора

Страница: 126 / 150

A-2
BHK-MG 1/2 (OPR) 030916
events of the Standard Event Status Enable Register are logically ORed to cause ESB (bit 5) of the
Status Byte Register to be set (1 = set = enable function, 0 = reset = disable function). (See example,
Figure A-1.)
A.5 *ESR? — EVENT STATUS REGISTER QUERY
*ESR?
Syntax : *ESR?
Return value: <integer> (Value = contents of Event Status register as defined in Table A-2.)
Description: Reads the Standard Event Status register, clearing the register at the same time. The Standard
Event Status register bit configuration is defined in Table A-2 (1 = set, 0 = reset). The error bits listed in
Table A-2 are also related to error codes produced during parsing of messages and to errors in the
power supply (see PAR. B.80). Related Commands: *CLS, *ESE, *OPC. (See example, Figure A-1.)
A.6 *IDN? — IDENTIFICATION QUERY
*IDN?
Syntax : *IDN?
Return value: Character string
Description: Identifies the instrument. This query requests identification. The power supply returns a string
which contains the manufacturer name, the model, the serial number and the firmware level. The
character string contains the following fields: <Manufacturer>, <Model>-<Voltage>-<Current> <Cali-
bration Date>,<Serial number>,<Firmware revision> where: <Manufacturer> = KEPCO, <Model> =
BHK, <Voltage> is Eo
MAX
, <Current> is Io
MAX
) <Calibration Date> is up to 10 characters entered dur-
ing calibration (recommended is month, day year: MM-DD-YYYY), <Serial number> E123456 is typi-
cal, <Firmware revision>=Vn.m (n.m revision, e.g, 7.0) (See example, Figure A-1.)
A.7 *OPC — OPERATION COMPLETE COMMAND
*OPC
Syntax : *OPC
Description: Causes power supply to set status bit 0 (Operation Complete) when pending operations are
complete.
This command sets Standard Event Status Register bit 0 (see Table A-2) to “1” when all
previous commands have been executed and changes in output level have been completed. This
command does not prevent processing of subsequent commands, but bit 0 will not be set until all
pending operations are completed. (1 = set = enable function, 0 = reset = disable function). (See
example, Figure A-1.) As an example, the controller sends command(s), then sends *OPC. If control-
ler then sends *ESR?, the power supply responds with either a “0” (if the power supply is busy execut-
ing the programmed commands), or a “1” (if the previously programmed commands are complete).
(See example, Figure A-1.)
A.8 *OPC? — OPERATION COMPLETE QUERY
*OPC?
Syntax : *OPC?
Return value: <1> (ASCII) placed in output queue when power supply has completed operation.
Description: Indicates when pending operations have been completed. When all pending operations are com-
plete (all previous commands have been executed and changes in output level have been completed)
a “1” is placed in the Output Queue. Subsequent commands are inhibited until the pending operations
are completed. *OPC? is intended to be used at the end of a command line so that the application pro-
gram can monitor the bus for data until it receives the “1” from the power supply Output Queue. (See
example, Figure A-1.)
A.9 *RCL — RECALL COMMAND
*RCL
Syntax : *RCL <integer> (1 to 40)
Description: Restores power supply to previously defined levels of output voltage, output current, overvolt-
age protection, and overcurrent protection.
This command selects one of the 40 power supply
memory locations, each of which stores values for output current, output voltage, overvoltage protec-
tion, and overcurrent protection. The following parameters are affected by *RCL: CURR[:LEV][:IMM]
VOLT[:LEV][:IMM] CURR:PROT[:LEV] VOLT:PROT[:LEV]. (See example, Figure A-1.)