Kenwood TK-2170 SERIES Скачать руководство пользователя | Manualshive

Страница: 19 / 142

background image

1 BASIC FUNCTIONS

FUNC (K)/Ver. 1.01

Confidential

7

1.13 Battery Saver

Battery Saver turns Off the receiver circuits periodically to
reduce battery consumption.
The transceiver receives intermittently in the following
conditions:

• While no carrier is detected.

• If no key is pressed for more than 5 seconds while a

carrier is detected and the QT/DQT does not match.

A user may have a chance to miss a call when the
transceiver receives a call while Battery Saver is enabled.
To avoid this, the transmitting party must be delayed to
talk or sending data after the transceiver starts
transmitting.
Battery Saver can be configured by using KPG-101D.
Following are the duration of intermittent reception.

Table 1-9 Intermittent Reception Intervals

Figure 1-5 Battery Saver

Configuration using KPG-101D

• Configuring the Battery Saver (Refer to FPRG

6.7.2 Common Page 2 Tab - Battery Saver.)

1.14 Mode Reset Timer

Mode Reset Timer is used to exit from Special Mode or
reset other statuses.
There are several Special Modes in the transceiver.
When the transceiver enters Special Mode, the current
Special Mode display appears on the display.
Key functions configured in Key Assignment cannot be
used since the following keys are fixed.
•

[S]

Key

•

[A]

Key

•

[<B]

Key

•

[C>]

Key

•

Side 1

Key

•

Side 2

Key

•

Selector

• 12-key keypad

(TK-2170 K2/ TK-3170 K4/ TK-3170 K6 only)

With the Mode Reset Timer, the transceiver can
automatically and reliably exit from Special Mode.
The Mode Reset Timer is used for the following Special
Modes and other statuses.

Table 1-10 Available Special Modes for

Mode Reset Timer

Note:

“PASSWORD” appears on the display when the Mode
Reset Timer expires in Transceiver Password Mode.

Configuration using KPG-101D

• Configuring the Mode Reset Timer (Refer to

FPRG 6.7.1 Common Page 1 Tab - Mode Reset
Timer.)

Battery Saver

QT/DQT or

Optional Signaling

Not Configured

QT/DQT or

Optional Signaling

Configured

Off

Off

Off

On

800 ms

200 ms

Off

Off

Saver On

800 or 200 ms

2-tone Encode List Select Mode

Autodial Mode

Autodial Programming Mode

Channel Entry Mode

OST List Select Mode

Transceiver Password Mode

Scrambler Code Select Mode

Selcall Mode

Squelch Level Adjustment Mode

Stack Mode

Status Mode

VOX Level Adjustment Mode

«
...
17
18
19
20
21
...
»

Содержание TK-2170 SERIES















































































































































Отзывы:

Нет отзывов

Похожие инструкции для TK-2170 SERIES

Бренд: Wacker Neuson Страницы: 92

Бренд: Rapid Страницы: 2

Бренд: Cross Tools Страницы: 68

Бренд: Powermate Страницы: 12

Бренд: Grundig Страницы: 75

Бренд: Sirius XM RAdio Страницы: 26

TransSteel 2200

Бренд: Fronius Страницы: 136

Бренд: nedis Страницы: 28

Бренд: Binatone Страницы: 2

Бренд: Albrecht Audio Страницы: 48

Бренд: iLive Страницы: 24

Бренд: Briggs & Stratton Страницы: 8

WEDECO SMOevo PLUS Series

Бренд: Xylem Страницы: 179

TOWER LIGHT CUBE+ HYBRID

Бренд: Generac Power Systems Страницы: 74

Бренд: Uniden Страницы: 84

Бренд: Philips Страницы: 1

Бренд: Philips Страницы: 12

Бренд: Philips Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды