Kenwood TK-2170 SERIES Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 142

Kenwood TK-2170 SERIES Скачать руководство пользователя страница 89

19 2-TONE

FUNC (K)/Ver. 1.01

Confidential

77

19.2.2 Duration of 2nd Tone

The Duration of 2nd Tone can be used to configure the
2nd Tone Encode duration for transmitting the 2-tone
configured for the 2-tone Encode Memory List.
The Duration of 2nd Tone can be configured by using
KPG-101D. Normally, the Duration of 2nd Tone is
configured for 3 seconds.

Configuration using KPG-101D

•

Configuring the Duration of 2nd Tone (Refer to
FPRG 6.11.1 Encode Tab - Duration of 2nd Tone.)

19.2.3 Duration of Single Tone

The Duration of Single Tone is the Single Tone Encode
duration for transmitting the Single Tone configured for
the 2-tone Encode Memory List.
The Duration of Single Tone can be configured by using
KPG-101D. Normally, the Duration of Single Tone is
configured for 5 seconds.

Configuration using KPG-101D

•

Configuring the Duration of Single Tone (Refer to
FPRG 6.11.1 Encode Tab - Duration of Single
Tone.)

19.2.4 Gap Time

The Gap Time can be used to configure the period of no
modulation between the 1st Tone and 2nd Tone used for
transmitting the 2-tone configured in the 2-tone Encode
Memory List.
The Gap Time can be configured by using KPG-101D.
Normally, the Gap Time is configured for 0 ms.

Configuration using KPG-101D

•

Configuring the Gap Time (Refer to FPRG 6.11.1
Encode Tab - Gap Time.)

19.2.5 First Tone Delay Time

The First Digit Delay Time is the time between when the
transceiver starts transmitting a 2-tone and when the
transceiver actually starts transmitting the 2-tone tone.
During the First Tone Delay Time, the transceiver
transmits an unmodulated signal.
The First Tone Delay Time can be configured by using
KPG-101D.

Configuration using KPG-101D

•

Configuring the First Tone Delay Time (Refer to
FPRG 6.11.1 Encode Tab - First Tone Delay
Time.)

19.2.6 Sidetone

Sidetone can be used to monitor the 2-tone tones when
the transceiver transmits 2-tone signaling.
The Sidetone can be configured to be monitored by using
KPG-101D.

Configuration using KPG-101D

•

Configuring the Sidetone (Refer to FPRG 6.11.1
Encode Tab - Sidetone.)

19.2.7 2-tone Encode Memory List

2-tone Encode Memory List is the code list for encoding
the 2-tone. The transceiver transmits the 2-tone when
the code configured for the list is selected.
The following functions can be configured for the 2-tone
Encode Memory List.

Table 19-1 2-tone Encode Memory List Configuration

Configuration using KPG-101D

•

Configuring the Single Tone (Refer to FPRG
6.11.1 Encode Tab - Single Tone.)

•

Configuring the 2-tone Name (Refer to FPRG
6.11.1 Encode Tab - 2-tone Name.)

•

Configuring the 1st Tone (Refer to FPRG 6.11.1
Encode Tab - 1st Tone.)

•

Configuring the 2nd Tone (Refer to FPRG 6.11.1
Encode Tab - 2nd Tone.)

2-tone Encode

Memory List

Operation

Single Tone

The code sent for each list number can be
configured as a Single Tone. 2nd Tone
cannot be configured if Single Tone is
configured.

2-tone Name

2-tone Name can be used to assign a name
to each list number. A maximum of 8
characters can be configured for the
2-tone Name.

1st Tone

The 1st Tone frequency can be configured.
The frequency can be configured between
288.5 and 3106.0 Hz.

2nd Tone

The 2nd Tone frequency can be configured.
The frequency can be configured between
288.5 and 3106.0 Hz.
2nd Tone cannot be configured if Single
Tone is configured.

«
...
87
88
89
90
91
...
»

Содержание TK-2170 SERIES















































































































































Отзывы:

Нет отзывов