Kenwood TK-2170 SERIES Скачать руководство пользователя | Manualshive

Страница: 101 / 142

background image

20 FLEETSYNC

FUNC (K)/Ver. 1.01

Confidential

89

20.3.3 Reserved Status for Status

Messages

Status Message has reserved statuses. Below is a list of
reserved status.

Table 20-8 Reserved Status List

Emergency

Alert Tone configured for Emergency Status
Response sounds when receiving a reserved Status.

Remote Stun

Remote Stun can be used to disable almost all the
transceiver’s functions. Only the following operations
are available when Stun is enabled. The transceiver
recovers from the Stun status when receiving the Stun
Deactivation status message or the DTMF Stun
Deactivation command.

Table 20-9 Operation when Stun Enabled

Statuses 90 to 92

These statuses are used to activate or reset Stun.
The statuses are enabled regardless of the Stun
status in the receiving party’s transceiver.

Statuses 93 to 94

These statuses are used to respond with the Stun
status of the transceiver when receiving the RSTM
(Request Status).

Status

Function

Operation at

Receiving Side

Entry of Status with

Entry Method

Manual

Dial

PC

Control

10 to 79

Statuses
intended for
users

Normal Status
operation.

Yes

Yes

80

Default Status

-

Yes/ No

*1

81 to 87 Undefined

-

88

Emergency
Reset Command

Exits from
Emergency
Mode.

89

Horn Alert
Activation
Command

-

90

Remote Stun
Transmit
Restriction
Command

The transceiver
sends the ACK.
Transmission is
restricted. “93”
is configured for
Current Status.

*2

91

Remote Stun
Transmit and
Receive
Restriction
Command

The transceiver
sends the ACK.
Transmission
and reception
are restricted.
“94” is
configured for
Current Status.
*2

92

Remote Stun
Reset Command

The transceiver
sends the ACK.
Disables Stun.
“80” is
configured for
Current Status.

93

Remote Stun
Transmit
Restriction
Response

-

94

Remote Stun
Transmit and
Receive
Restriction
Response

-

95 to 99

Reserved Status
for Emergency
Mode
98: Man-down
Status
99: Emergency
Status other
than Man-down

The transceiver
sends the ACK.
Alert/ Horn/
None

*3

*1

Entry of Statuses 80 to 99 can be enabled or disabled by using

KPG-101D when directly entering a status number with Manual
Dialing.

(Refer to 20.3.9 Status 80 - 99 (Special) on page 91.)

*2

Stun Status does not change even if a user changes the Status in

Status Mode.

*3

Entry of Statuses 95 to 99 in Emergency Mode can be configured

to be enabled or disabled by using KPG-101D.

(Refer to 20.3.9

Status 80 - 99 (Special) on page 91.)

Status Message

Transmit

Restriction

Transmit and

Receive Restriction

Normal Status

Message

operation

Transmit Restriction

Transmit and
Receive Restriction

PC Control

The transceiver does
not accept a
transmission request.
The transceiver does
not send received
data.

The transceiver does
not accept a
transmission request.
The transceiver does
not send received
data.

«
...
99
100
101
102
103
...
»

Содержание TK-2170 SERIES















































































































































Отзывы:

Нет отзывов

Похожие инструкции для TK-2170 SERIES

Бренд: Radius Страницы: 7

Бренд: Galaxy Страницы: 38

Бренд: MagicBox Страницы: 20

Бренд: Salora Страницы: 35

Бренд: ELBE Страницы: 2

Бренд: Pulsar Страницы: 26

Бренд: Sangean Страницы: 11

Бренд: C. Crane Страницы: 35

Бренд: Firman Страницы: 114

Бренд: Sunwave Страницы: 47

Бренд: MULTIQUIP Страницы: 4

Бренд: LENCO Страницы: 25

Бренд: Cirro Страницы: 8

Бренд: Vertex Standard Страницы: 10

Бренд: Ocean Digital Страницы: 26

Бренд: Chinavision Страницы: 14

Бренд: Vertex Standard Страницы: 32

Бренд: PRESIDENT Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды