Kenwood TK-2170 SERIES Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 142

Kenwood TK-2170 SERIES Скачать руководство пользователя страница 73

17 OST

FUNC (K)/Ver. 1.01

Confidential

61

17.3 Direct OST

Direct OST can be used to select OST by using the
keypad.
Direct OST can be configured to be enabled or disabled
by using KPG-101D.

Transceiver Operation

z

Selecting OST List 1 to 9
1.

Press and hold one of the

[1]

to

[9]

keys for

more than 1 second.
The OST Name appears on the display for 2
seconds.

z

Selecting OST List 1 to 40
1.

Press and hold the

[*]

key for 1 second.

The transceiver enters List Number Enter
Mode.

2.

Enter the OST List number.

The OST Name appears for 2 seconds if a
configured OST number is entered.

The channel name or number appears on the
display after the OST Name disappears.

z

Selecting Tone Off
1.

Press and hold the

[0]

key for more than 1

second.
“TONE OFF” appears on the display for 2
seconds.

z

Disabling OST
1.

Press and hold the

[#]

key for more than 1

second.
The OST icon disappears.

Configuration using KPG-101D

•

Configuring the OST (Refer to FPRG 6.8.2
General Tab - Keypad Operation.)

17.4 OST Table

OST Table can be used to configure a QT/DQT Decode/
Encode pair for OST. A maximum of 40 pairs can be
configured. The following functions can be configured for
the OST Table.

Table 17-1 OST Table Configuration

Configuration using KPG-101D

•

Configuring the OST Name (Refer to FPRG 6.7.3
Conventional Tab - OST Name.)

•

Configuring the QT/DQT Decode (Refer to FPRG
6.7.3 Conventional Tab - QT/DQT Decode.)

•

Configuring the QT/DQT Encode (Refer to FPRG
6.7.3 Conventional Tab - QT/DQT Encode.)

OST Table

Configuration

OST Name

OST Name can be used to assign a
name to an OST QT/DQT Encode/
Decode pair. A maximum of 8
characters can be entered.
“TONE 1” to “TONE 40” appears on
the display if no OST Name is
configured.

QT/DQT Decode

The QT/DQT Decode code used for
receiving a call can be configured.
The following QT/DQT Decode
range is available.
QT: 67 to 254.1 Hz/ 0.1 Hz steps
DQT: 000N to 777N, 000I to 777I

QT/DQT Encode

The QT/DQT used to make a call
can be configured. The following
QT/DQT Encode range is available.
QT: 67 to 254.1 Hz/ 0.1 Hz steps
DQT: 000N to 777N, 000I to 777I

«
...
71
72
73
74
75
...
»

Содержание TK-2170 SERIES















































































































































Отзывы:

Нет отзывов