Kenwood TK-2170 SERIES Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 142

Kenwood TK-2170 SERIES Скачать руководство пользователя страница 81

18 DTMF

FUNC (K)/Ver. 1.01

Confidential

69

18.2.8 Manual Dialing

Manual Dialing allows a user to send a DTMF code
corresponding to a particular key when the

[0]

to

[9]

,

[*]

,

or

[#]

key on the Mic keypad is pressed while transmitting

by pressing the

PTT

switch.

Manual Dialing can be configured to be enabled or
disabled by using KPG-101D.

Configuration using KPG-101D

•

Configuring the Keypad Operation (Refer to
FPRG 6.8.2 General Tab - Keypad Operation.)

•

Configuring the Manual Dialing (Refer to FPRG
6.10.1 Encode Tab - Manual Dialing.)

18.2.9 Store & Send

When using Store & Send, the desired series of DTMF
codes can be entered via the keypad, but then be sent at
a later time. A maximum of 16 digits can be transmitted
in a single Store & Send operation.
Store & Send can be configured to be enabled or
disabled by using KPG-101D.

Configuration using KPG-101D

•

Configuring the Store & Send (Refer to FPRG
6.10.1 Encode Tab - Store & Send.)

18.2.10 Dial ID

Dial ID can be configured to be enabled or disabled.
Dial ID can be used to send the BOT and EOT codes of
the DTMF PTT ID configured for the channel by pressing
the

[*]

+

[*]

or

[*]

+

[#]

keys on the keypad.

Dial ID can be configured to be enabled or disabled by
using KPG-101D.

Configuration using KPG-101D

•

Configuring the Dial ID (Refer to FPRG 6.10.1
Encode Tab - Dial ID.)

18.2.11 Auto Telephone

(TK-3173 only)

Auto Telephone can be configured to be enabled or
disabled. Auto Telephone can be used if the

Side 2

key

is pressed in Autodial Mode.
Auto Telephone can be configured to be enabled or
disabled by using KPG-101D.

Configuration using KPG-101D

•

Configuring the Auto Telephone (Refer to FPRG
6.10.1 Encode Tab - Auto Telephone.)

18.2.12 DTMF Sidetone

DTMF Sidetone can be used to make the transceiver emit
DTMF tones from the speaker when the transceiver
sends DTMF code.
DTMF Sidetone can be configured to be enabled or
disabled by using KPG-101D.

Note:

The transceiver does not emit the DTMF monitor tones in
Emergency Mode in the following conditions:
•

When “Silent” is selected from the

Emergency

Information

window >

Emergency Type

dropdown list.

•

When “DTMF” is selected from the

Emergency

Information

window >

Emergency Type

dropdown list.

Configuration using KPG-101D

•

Configuring the DTMF Sidetone (Refer to FPRG
6.10.1 Encode Tab - Sidetone.)

«
...
79
80
81
82
83
...
»

Содержание TK-2170 SERIES















































































































































Отзывы:

Нет отзывов