Kenwood TK-2170 SERIES Скачать руководство пользователя | Manualshive

Страница: 51 / 142

background image

FUNC (K)/Ver. 1.01

Confidential

39

14 CONVENTIONAL GROUP

Conventional Groups are groups of Simplex and Semi-
duplex Conventional Channels.
A zone can be configured for Conventional Group by
using KPG-101D.

14.1 Zone

The following functions relevant to the zone in
Conventional Group can be configured by using
KPG-101D:
•

Zone Name

•

Data Zone-channel

•

Home Channel

•

Operator Selectable Home-channel

•

Optional Signaling Decode Condition

•

Audio Control

•

Time-out Timer (TOT)

•

TOT Pre-alert

•

TOT Rekey Time

•

TOT Reset Time

•

Zone Add

•

Scan List

14.1.1 Zone Name

Zone Name can be used to assign a name to a zone.

(Refer to 3.4.1 Zone Name on page 15.)

Zone Name can be configured by using KPG-101D.

Configuration using KPG-101D

•

Configuring the Zone Name (Refer to FPRG 6.2.1
Zone Name.)

14.1.2 Data Zone-channel

Data Zone-channel can be used to separate channels for
data communications from channels for voice
communications.

(Refer to 23.1.2 Data Zone-CH/GID on

Data Zone-channel can be configured by using
KPG-101D.

Configuration using KPG-101D

•

Configuring the Data Zone-channel (Refer to
FPRG 6.2.2 Data Zone-CH/GID.)

14.1.3 Home Channel

This function can be used to jump to a frequently used
channel with a press of the key.

(Refer to 2.7 Home CH/

GID on page 10.)

The Home Channel can be configured by using
KPG-101D.

Note:

With this function, the transceiver can only jump to a
channel in the same zone.

Configuration using KPG-101D

•

Configuring the Home Channel (Refer to FPRG
6.2.3 Home Channel.)

•

Assigning functions to the

PF

keys (Refer to

FPRG 6.8 Key Assignment.)

14.1.4 Operator Selectable

Home-channel

Operator Selectable Home-channel can be used to
configure the Home Channel via transceiver operation.
A user can change the Home Channel by selecting the
channel to be configured as the Home Channel and
pressing and holding the

Home CH/GID

key for than 3

seconds while this function is enabled.
When the

Home CH/GID

key is pressed and held for

more than 3 seconds while Operator Selectable Home-
channel is enabled, the Home Channel can be changed.
Operator Selectable Home-channel can be configured to
be enabled or disabled by using KPG-101D.

Configuration using KPG-101D

•

Assigning functions to the

PF

keys (Refer to

FPRG 6.8 Key Assignment.)

•

Configuring the Operator Selectable Home-
channel (Refer to FPRG 6.2.4 Operator
Selectable Home-channel.)

«
...
49
50
51
52
53
...
»

Содержание TK-2170 SERIES















































































































































Отзывы:

Нет отзывов

Похожие инструкции для TK-2170 SERIES

Бренд: NANO Страницы: 28

Бренд: Pulsar Страницы: 26

Бренд: Troy-Bilt Страницы: 12

Бренд: A2Z Ozone Страницы: 13

IntelliChlor SCG

Бренд: Pentair Pool Products Страницы: 12

Бренд: Milwaukee Страницы: 11

Бренд: Cobra Страницы: 42

Бренд: North Star Страницы: 11

Бренд: Honda Страницы: 59

Бренд: CAMPAGNOLA Страницы: 70

Бренд: Soen Страницы: 39

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 2

Бренд: Toshiba Страницы: 80

Бренд: Toshiba Страницы: 76

Бренд: Toshiba Страницы: 100

Бренд: Toshiba Страницы: 100

Бренд: Toshiba Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды