KEM MKC-710 Скачать руководство пользователя страница 85

Страница: 85 / 133

6. Setup

MKC-710 75

[Printer]

Select a type of printer you are going to use:

Select “NONE” if no printer is

connected.

NONE

：

No printer.

IDP-

：

KEM’s impact dot printer model IDP

-100.

DP-USB

：

Select this when connecting our thermal printer (DP-600) to

the USB port.

OTHER

：

Other printer than the below.

Note

Connect to COM1 when selecting ‘IDP

‘ or ‘OTHER’. Connecting to COM2 leads

to failure in printing.

Note

For printer type and configurations, refer to the Table 6-1-3-1. The

communication protocol between your printer and titration unit must match.

Otherwise, printing may fail and halt halfway. For digital configurations for your

printer, refer to the operation manual for the printer.

[Baud Rate]

If you use other printer as defined on

［

Printer

］

, you have to select baud rate for your

printer:

300 bps /600 bps / 1200 bps / 2400 bps / 4800 bps / 9600 bps

[Parity]

If you use “Other” printer as defined on

［

Printer

］

, you have to select parity for your

printer:

NONE/EVEN/ODD

[Stop Bits]

If you use “Other” printer as defined on

［

Printer

］

, you have to select stop bits for

your printer:

1bit / 2bits

[Data Bits]

If you use “Other” printer as defined on “Printer”, you have to select data bit for your

printer:

7bits / 8bits

Table6-1-3-1

Printer

Cables

Titrator setup

Printer settings

Citizen

CBM-910
CBM-910

Type

Ⅱ

Connecting cable

12-02013
64-00625

Printer

IDP- Digital configurations for printer:

Baud rate

：

4800

Parity

：

none

Stop bits

：

Data bits

：

Содержание MKC-710






































































































































Результаты поиска

Содержание MKC-710

Отзывы:

Похожие инструкции для MKC-710

Бренды по названию

Популярные бренды

KEM MKC-710, Руководство по эксплуатации

Результаты поиска

Содержание MKC-710

Отзывы:

Похожие инструкции для MKC-710

Бренды по названию

Популярные бренды