Kathrein UFS 913 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 64

background image

47

If you now wish to set up an archive hard

disk, press the



button; if not, press

the



button to abort this procedure.

Now remove all hard disks or USB sticks
from the receiver and then con

fi

rm by

pressing the



button, or pressing

the



button to abort this procedure.

Now connect the hard disk that is to
be set up as an archive hard disk to the
receiver.

Now set the respective capacities for
the various areas (Media Centre and
Timeshift). The respective lines are

selected using the



buttons.

Make the settings using the



buttons. The storage volume that you
assign to each area is dependent on the
size of the hard disk being used.

The following on-screen display appears
(see screenshot on the right).

Connection and set-up

If you have aborted this procedure the
following on-screen display appears (see

screenshot on the right). Press the



button.

«
...
45
46
47
48
49
...
»

Содержание UFS 913

































































Отзывы:

Нет отзывов

Похожие инструкции для UFS 913

Бренд: Uniden Страницы: 17

Бренд: Yamaha Страницы: 57

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 60

Бренд: Zenith Страницы: 44

Бренд: ZENEC Страницы: 1

Бренд: Teac Страницы: 20

Бренд: Vega Страницы: 11

Бренд: Boss Audio Systems Страницы: 23

Бренд: FrSky Страницы: 3

Бренд: Jedia Страницы: 10

AM-FM Receiver 870-20

Бренд: Raymer Страницы: 4

Бренд: AMIMON Страницы: 56

Бренд: CAME Страницы: 8

Бренд: Boss Audio Systems Страницы: 8

Бренд: Marmitek Страницы: 64

Бренд: Onkyo Страницы: 110

Бренд: GME Electrophone Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды