Kathrein UFS 913 Скачать руководство пользователя страница 13

Страница: 13 / 64

For this, refer to the operating
instructions for your TV set and
take care to select only those
settings that your TV set can
process.

Press the



(green) button to move to the next menu.

The following on-screen display appears:

Use the



buttons here to select the basic

settings for the video and audio output of the
receiver to the TV set.

Video Output via

Select the connection on the receiver to which you have connected your television. Either

TV aspect ratio

Here you can select the TV picture format. Either

- 4:3

- 16:9

Picture format

Select the type of screen display, depending on
your setting for the TV aspect ratio:

- TV format “4:3”: Pan & Scan or Letterbox

- TV format “16:9”: Always 16:9 or Automatic

HDMI/YUV

SCART

HDMI/YUV Resolution

Here you can select the picture resolution that will
be sent to the TV set. Either

- 1080p (resolution 1920 x 1080, full-screen

images)

- 1080i (resolution 1920 x 1080, half-screen

images)

- 720p (resolution 1280 x 720, full-screen

images) or

- 576p (resolution 720 x 576, full-screen images)

- Automatic

Force 576i (must be supported by the TV set
otherwise you will not see a TV picture)

You can only and need only make this setting if
you have selected the setting “Automatic” for

Connection and set-up

Содержание UFS 913

































































Результаты поиска

Содержание UFS 913

Отзывы:

Похожие инструкции для UFS 913

Бренды по названию

Популярные бренды

Kathrein UFS 913, Руководство по эксплуатации

Результаты поиска

Содержание UFS 913

Отзывы:

Похожие инструкции для UFS 913

Бренды по названию

Популярные бренды