Kathrein UFS 913 Скачать руководство пользователя страница 46

Страница: 46 / 64

Connection and set-up

Automatic

Manual

You need not enter any further data, the receiver
will automatically update the date and time.

Use the number pad or the



buttons to

enter the correct date. Then use the



buttons to switch to the “Time”

eld and use the

number pad or the



buttons to enter the

correct time. Then use the



button to con

your entry.

Depending on the desired time setup option (Automatic/Manual) the following on-screen display then
appears:

When you have completed all settings, press the



(green) button, to complete the

rst installation.

Setup Time now

Press the



button.

Set up the archive hard disk

To make recordings using the UFS 913 and utilise the timeshifting and recording
archive functions you must connect an external hard disk

to the rear of the

receiver (USB) and set it up.

Tested only with hard disks from the Kathrein product range (see also:
www.kathrein.de

→

Service

→

FAQs)

Содержание UFS 913

































































Результаты поиска

Содержание UFS 913

Отзывы:

Бренды по названию

Популярные бренды

Kathrein UFS 913, Руководство по эксплуатации

Результаты поиска

Содержание UFS 913

Отзывы:

Бренды по названию

Популярные бренды