K&R ACD320 Series Скачать руководство пользователя страница 63

Страница: 63 / 160

ACD320 user manual

Parameter Description

- 58-

Value

F0.08

ACCELtime 1

0.1

～

3600.0s

10.0s

F0.09

DECEL time 1

0.1

～

3600.0s

10.0s

Acceleration time means the time t1 required for inverter to accelerate to the maximum

output frequency (F0.04) from 0Hz.

Deceleration time is the time t2 required for inverter to decelerate to 0Hz fromthe

maximumoutput frequency (F0.04).

It is indicated by following figure

Fig 6-1 Acceleration and Deceleration time diagram

When the set frequency is equal to the maximum frequency, the actual

Acceleration/Deceleration time are equal to the set Acceleration/Deceleration time.

When the set frequency is less than the maximum frequency, the actual

Acceleration/Deceleration time are less than the set Acceleration/Deceleration time.

Actual Acceleration /Deceleration time = set Acceleration/Deceleration time (set

frequency/max.frequency)

ACD320 series inverter has 2 groups ofAcceleration/Deceleration time.

1st group: F0.08, F0.09;

2nd group: F4.00, F4.01;

The Acceleration /Deceleration time can be chosen through multifunction digital input

terminal (F2 Group).

Содержание ACD320 Series

































































































































































Результаты поиска

Содержание ACD320 Series

Отзывы:

Бренды по названию

Популярные бренды

K&R ACD320 Series, Руководство пользователя

Результаты поиска

Содержание ACD320 Series

Отзывы:

Бренды по названию

Популярные бренды