K&R ACD320 Series Скачать руководство пользователя страница 60

Страница: 60 / 160

ACD320 user manual

Parameter Description

- 55-

F0.01

Command source

selection

0: Keyboard

1: Terminal

2: Communication

Path Selection for the inverter Control Command

0: Keyboard Command Path

The buttons RUN and STOP on the keyboard are for operation control.

1:Terminal Command Path

Multifunction input terminals of forward, reverse, forward jogging, reverse jogging and so

on, perform the operation command control.

2:Communication Command Path

Operation command control is performed through communication pattern by upper level

machine.

Function Code

Name

Setting Range

Default

Value

F0.02

Keyboard

and

terminal

UP/DOWN setting

0: Valid,

and

inverter

memorize

when

power

down
1: Valid, and inverter does
not memorize when power
down
2: Invalid

ACD320 series inverter can set up the frequency though "

∧

" and "

∨

" buttons on the

keyboard and terminal UP/DOWN (Frequency setting increase /Frequency setting decrease), and

as it has the highest purview, it can combine with any other frequency setting path tomainly

accomplishes the fine adjustment of inverter output frequency during control system

commissioning.

0: Valid, and the inverter memorizes when power down.Able to set up frequency command,

and memorize this set frequency when the inverter is power down.When the power is

back,automatically combine it with current frequency setting.

1: Valid, and the inverter does notmemorize when power is down.Able to set up

frequency,but when the inverter power is down, this frequency setting is not memorized.

2: Invalid. The frequency set through keyboard and terminal UP/DOWN is automatically

cleared,and the settings through keyboard and terminal UP/DOWN are invalid.

Note: After the user restores the default values of inverter function parameters, the

Содержание ACD320 Series

































































































































































Результаты поиска

Содержание ACD320 Series

Отзывы:

Бренды по названию

Популярные бренды

K&R ACD320 Series, Руководство пользователя

Результаты поиска

Содержание ACD320 Series

Отзывы:

Бренды по названию

Популярные бренды