K&R ACD320 Series Скачать руководство пользователя страница 36

Страница: 36 / 160

ACD320user manual

Installation and wiring

- 31-

EMI issue is mainly toreduce the EMI of inverter.

Methods:

A) Inverter and other equipment shall be well grounded and the grounding resistance shall be

less than 5ohm.

B) Inverter's power cables shall be vertical instead of parallel with the control cables.

C) For the applicationwith strong disturbance, the power cables from the motor to the inverter

shall be shielded and the shielding layer shall be grounded.

D) The cables of disturbed equipment shall be twisted shielded cables and the shielding layer

shall be grounded.

2) Reducing the disturbance to the inverter from other equipment

The relay, contactor or electronic -magnetic braking device will disturb the inverter.

Take the following actions to solve this issue:

A) Install surge suppressing devices to the disturbing device

B) Install filter to the input of the inverter

C) Inverter's control cables shall be shielded and the shielding layer shall be grounded

3)Method to reduce the disturbance fromthe inverter to the equipment

Two kinds of noises, one is the radiation from the inverter itself, and another is the radiation from

the cable between the inverter and the motor. These two kinds of radiations induce the cables of

the equipment and make the equipment work abnormally. Following method can be used:

A) If themeasuring meters, radio equipment and sensors and their signal cables are installed in a

cabinet together with the drive, these equipment cableswill be easily disturbed. Take the actions

below to solve the problem: The equipment and the signal cables should be as far away from the

inverter as possible; Signal cables and power cables shall not be routed in parallel or bound

together; The signal and power cables should be shielded; Install radio noise filter and linear

noise filter at the input and output sides of the inverter.

B) If the external equipment shares a sameAC supply with the inverter, and the above cannot

eliminate the disturbance, then the user should install a linear filter or a radio noise filter.

Содержание ACD320 Series

































































































































































Результаты поиска

Содержание ACD320 Series

Отзывы:

Бренды по названию

Популярные бренды

K&R ACD320 Series, Руководство пользователя

Результаты поиска

Содержание ACD320 Series

Отзывы:

Бренды по названию

Популярные бренды