JUKI AMS-210E-1306 Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 128

background image

– 120 –

3

1

4

2

1-12. Replenishing the designated places with grease

* Perform grease supplement when the errors below are displayed or once a year (either one

which is earlier). After performing grease supplement, call memory switch No. 245 and set the
value to "0" with the reset key.

When the sewing machine has been used for a certain number of times of sewing, error code No.
E220 is displayed on the operation panel at the time of turning ON the power. This display informs the
operator of the time of replenishing the designated places with grease. Be sure to replenish the places
with the grease below. Then call the memory switch No. 245 and set it to "0" with the RESET key.
Even after the display of the error No. E220, when the RESET key is pressed, the error is released, and
the sewing machine can be continuously used. Afterwards, however, the error No. E220 is displayed
every time the power is turned ON.
In addition, when the sewing machine is used further for a certain period of time after the display of
error No. E220, the error No. E221 is displayed and the sewing machine fails to operate since the error
cannot be released even when the RESET key is pressed.
When the error No. E221 is displayed, be sure to replenish the designated places below with grease.
Then start up the memory switch and set No. 245 to "0" with the RESET key.

1. After replenishing the places with grease, the error No. E220 or No. E221 is

displayed again unless the memory switch No. 245 is changed to "0".

2. Use grease tube (Part No. 40013640) supplied as accessories to replenish the

designated places below with grease.If grease other than the designated one is
replenished, damage of components will be caused.

(1) Replenishing the eccentric cam section with grease

1) Open the upside cover

1

and remove the

grease

2

.

2) Remove rubber cap

4

located on the side of

eccentric cam

3

. Then replenish there with

grease.

WARNING :

Turn OFF the power before starting the work so as to prevent accidents caused by abrupt start of the

sewing machine.

«
...
122
123
124
125
126
...
»

Содержание AMS-210E-1306

































































































































Отзывы:

Нет отзывов

Похожие инструкции для AMS-210E-1306

Бренд: DHS Fitness Страницы: 9

Zero Pulsar Plus 55-S

Бренд: Clemco Страницы: 47

Бренд: DURKOPP ADLER Страницы: 24

Бренд: Numatic Страницы: 52

Бренд: Insportline Страницы: 9

TRIDENT T26 SC PLUS

Бренд: Hillyard Страницы: 28

Бренд: Kärcher Страницы: 15

Бренд: Tennant Страницы: 155

Бренд: Nobles Страницы: 1

Бренд: Singer Страницы: 39

Бренд: JUKI Страницы: 14

Бренд: JUKI Страницы: 100

Бренд: Sanyo Страницы: 44

Бренд: Sanyo Страницы: 63

Бренд: Sanyo Страницы: 74

Бренд: Sanyo Страницы: 77

Бренд: Sanyo Страницы: 71

Бренд: Sanyo Страницы: 83

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды