JUKI AMS-210E-1306 Скачать руководство пользователя страница 123

Страница: 123 / 128

– 119 –

1-11. Changing the voltage of 100

200V

WARNING :

To prevent personal injuries caused by electric shock hazards or abrupt start of the sewing

machine, carry out the work after turning OFF the power switch and a lapse of 5 minutes or more.

To prevent accidents caused by unaccustomed work or electric shock, request the electric expert

or engineer of our dealers when adjusting the electrical components.

Changing procedure of the changeover connector

1. Turn OFF the power source with the power switch

after conﬁrming that the sewing machine has

stopped.

2. Draw out the power cord from the power plug

socket after conﬁrming that the power switch is

turned OFF. Then wait for ﬁve minutes or more.

3. Remove the front cover.

4. Remove four screws ﬁxing the rear cover of the

control box and slowly open the rear cover.

A. In case of using with 3-phase 200V to 240V

• Changing the changeover connector

Connect to 200V the 100/200V changeover

connector of FLT p.c.b.

located on the side

of the Box Side of the control box.

• Connect the crimp style terminal of AC input

cord to the power plug as shown in the ﬁgure.

B. In case of using with single phase 100V to 120V

• Changing the changeover connector

Connect to 100V the 100/200V changeover

connector of FLT p.c.b.

located on the side

of the Box Side of the control box.

• Connect the crimp style terminal of AC input

cord to the power plug as shown in the ﬁgure.

(Caution) Securely perform the insulation

treatment to the red terminal which is not used

with insulation tape or the like. (When the

insulation is insufﬁcient, there is a danger of

electric shock or leakage current.)

C. In case of using with single phase 200V to 240V

• Changing the changeover connector

Connect to 200V the 100/200V changeover

connector of FLT p.c.b.

located on the side

of the Box Side of the control box.

• Connect the crimp style terminal of AC input

cord to the power plug as shown in the ﬁgure.

(Caution) Securely perform the insulation

treatment to the red terminal which is not used

with insulation tape or the like.

(When the insulation is insufﬁcient, there is a

danger of electric shock or leakage current.)

5. Check that the change has been performed

without fail before closing the rear cover.

6. Be careful that the cord is not pinched between

the rear cover and the control box main unit.

Close the rear cover while pressing the lower

side of rear cover, and tighten four screws.

It is adaptable to the voltage of single phase 100V to 120V/3-phase 200V to 240V by changing the voltage

changeover connector mounted on FLT p.c.b.

(Caution) When the changing procedure is wrong, the control box will be broken. So, be very careful.

GREEN/

YELLOW

(Plug side)

WHITE

BLACK

RED

WHITE
BLACK
RED

GREEN/

YELLOW

GREEN/

YELLOW

(Plug side)

WHITE

BLACK

RED

GREEN/

YELLOW

(Plug side)

GREEN/

YELLOW

GREEN/

YELLOW

WHITE
BLACK
RED

WHITE

BLACK

RED

WHITE
BLACK
RED

Содержание AMS-210E-1306

































































































































Результаты поиска

Содержание AMS-210E-1306

Отзывы:

Похожие инструкции для AMS-210E-1306

Бренды по названию

Популярные бренды

JUKI AMS-210E-1306, Инструкция по эксплуатации

Результаты поиска

Содержание AMS-210E-1306

Отзывы:

Похожие инструкции для AMS-210E-1306

Бренды по названию

Популярные бренды