JUKI AMS-210E-1306 Скачать руководство пользователя страница 28

Страница: 28 / 128

– 24 –

5) Removing procedure of the smart media

Open the smart media cover, push the card until it goes no further, and ease up force when it

goes to the end. The card returns by approximately 10 mm in the reverse order of the time of
setting.

Then draw out the card to complete removing.

4) Inserting direction of the smart media

Insert the smart media in the direction as shown in the ﬁgure for both IP-400 and the CP-20.

After completion of setting of the card, close the smart media cover. By closing the cover, it is

possible to perform communication. If the smart media card and the cover come in contact with
each other and the cover is not closed, check the following matters.

• Check that the inserting is stopped in the state that the card protrudes by approximately 10 mm.

• Check that the contact part of the card is put downward and inserted.

• Check that the smart media card other than 3.3V voltage type is used.

Smart media

Be sure to use the smart media that has been formatted with IP-400.
For the formatting procedure of the smart media, refter to

-2-26. Performing formatting of the smart media"

Содержание AMS-210E-1306

































































































































Результаты поиска

Содержание AMS-210E-1306

Отзывы:

Похожие инструкции для AMS-210E-1306

Бренды по названию

Популярные бренды

JUKI AMS-210E-1306, Инструкция по эксплуатации

Результаты поиска

Содержание AMS-210E-1306

Отзывы:

Похожие инструкции для AMS-210E-1306

Бренды по названию

Популярные бренды