JUKI AMS-210E-1306 Скачать руководство пользователя страница 81

Страница: 81 / 128

– 77 –

Display the smart media format screen.

When MODE key

is held pressed for three seconds,

smart media format button

is displayed on the screen.

When this button is pressed, the smart media format screen is
displayed.

Start formating of the smart media.

Set the smart media you desire to format to the smart media
slot, close the cover, press ENTER button

and

formating starts.

Save necessary data in the smart media to the other vehicle
before formating. When formating is performed, the inside
data are deleted.

2-26. Performing formatting of the smart media

When re-formatting the smart media, be sure to perform it with IP-400. The smart media that is
formatted with the personal computer cannot be read with IP-400 and the CP-20.

Содержание AMS-210E-1306

































































































































Результаты поиска

Содержание AMS-210E-1306

Отзывы:

Похожие инструкции для AMS-210E-1306

Бренды по названию

Популярные бренды

JUKI AMS-210E-1306, Инструкция по эксплуатации

Результаты поиска

Содержание AMS-210E-1306

Отзывы:

Похожие инструкции для AMS-210E-1306

Бренды по названию

Популярные бренды