Jonsered FR 13 Скачать руководство пользователя страница 62

Страница: 62 / 68

Engine runs unevenly or
feels weak

Engine overheating

ENGINE ST

AR
TS BUT

DOES NOT

WORK SA

TISF

ACT

ORIL

Exhaust
fumes:

Strong Blue Black

Engine damage
Perform compression test

Ignition fault

Fuel fault

Ignition fault

Carburettor problems

Insufficient cooling

Incorrect fuel type.
Petrol too old.
Low octane number after
long storage.
Replace petrol

Overloading
Change driving style

Choking

Check choke cable and
choke valve

Spark plug defective

Incorrect ignition setting

Diode failure (V-twin
engine)
Replace diode

Too little fuel in tank

Soiled fuel filter

Dirt in fuel hose
Constricted or badly sealed
fuel hose

Faulty carburettor

Blocked air filter

Tank ventilator blocked

Spark plug has wrong
thermal value

Pre-ignition incorrect

Diode failure (V-twin
engine)

Incorrect setting

Partially or completely
blocked needles and
diffuser jets

Too little or no oil in the
engine

Blocked cooling fins or
air intake

Cooling fan damaged

Extremely worn or blocked

Incorrect thermal value

Incorrect electrode gap

Incorrect pre-ignition
position

Fill fuel tank

Change filter

Clean or replace fuel hose

Incorrect settings

Blocked needles

Clean or replace fuel cap

Clean or replace filter

Replace with right spark
plug

Correct ignition setting

Replace diode

Correct setting

Clean carburettor with
compressed air

Fill with right quality and
amount of oil

Clean out dirt and leaves

Replace fan and clean fan
cover

Clean, adjust, or replace
plug

Replace with spark plug
with right thermal value

Check and adjust
electrode gap

Adjust pre-ignition

Correct the carburettor
setting

Clean carburettor with
compressed air

Содержание FR 13





































































Результаты поиска

Содержание FR 13

Отзывы:

Похожие инструкции для FR 13

Бренды по названию

Популярные бренды

Jonsered FR 13, Руководство по ремонту

Результаты поиска

Содержание FR 13

Отзывы:

Похожие инструкции для FR 13

Бренды по названию

Популярные бренды