Jonsered FR 13 Скачать руководство пользователя страница 56

Страница: 56 / 68

– English

6012-083

6012-084

6012-086

6012-085

6012-087

Loosen the four screws that hold the blade bear-
ings and remove the entire bearing assembly from
the cutting unit.

Remove the hub using a puller. Do not lose the key
that sits between the hub and the axle.

Remove the protective metal washer.

• Push out the axle with a puller.

• Tap out the bearing and remove the spacer.

You can purchase the entire assembly, complete
with axle housing, axle, spacer, and bearings.

Assemble in the reverse order as described for
dismantling.

IMPORTANT INFORMATION

When tightening the blade axle screws,
the transmission side should always be
tightened first and then the blade screws.

When the blades on the mulching unit
have been removed, the friction disc
located between the blade and nut must
be replaced.

Make sure that the axle is mounted in the same
direction as when it was removed, otherwise the
keys will not fit the slots.
Tighten the blade bearings with a torque of
20-25 Nm.

Repair Instructions

Содержание FR 13





































































Результаты поиска

Содержание FR 13

Отзывы:

Похожие инструкции для FR 13

Бренды по названию

Популярные бренды

Jonsered FR 13, Руководство по ремонту

Результаты поиска

Содержание FR 13

Отзывы:

Похожие инструкции для FR 13

Бренды по названию

Популярные бренды