Jonsered FR 13 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 68

background image

44

– English

8 9

8009-132

6017-157

6012-057

Removing Belt

Starting position for removing belt:

• No unit is attached to the machine.

• The front part of the belt is loose.

The entire belt is removed according to the follow-
ing only when a snow blade is to be attached to the
machine.

1. Loosen the belt guides and the support pulley.

2. Loosen the wheel on the belt tensioner.

3. Ease off the belt from the middle pulley and

remove the belt.

To fit the belt, follow the removal instructions in the
reverse order.

Changing the Oil in Hydrostatic Machines

Empty the hydrostatic transmission by means of the
two 14 mm plugs, the other screws are smaller in
size.

Fill the oil tank with oil.

Air the transmission as described in Airing the
Hydrostatic Transmission’s Oil System. Fill with oil
as needed during airing.
Test run the machine and check the oil level.

IMPORTANT INFORMATION

Used oil is an environmental hazard and
must not be disposed of on the ground or
in nature; it should always be disposed of
at a workshop or appropriate disposal
location.

Avoid skin contact; wash with soap and
water in case of spills.

Repair Instructions

«
...
44
45
46
47
48
...
»

Содержание FR 13





































































Отзывы:

Нет отзывов

Похожие инструкции для FR 13

Бренд: Cadet Страницы: 40

Бренд: Yard-Man Страницы: 16

Greens King V Plus

Бренд: Jacobsen Страницы: 224

Бренд: Gardena Страницы: 13

Бренд: Simplicity Страницы: 54

Бренд: Hayter Страницы: 40

Бренд: Poulan Pro Страницы: 48

Бренд: Stihl Страницы: 436

EcoCut 135 Z-042

Бренд: Talex Страницы: 164

Бренд: MTD Страницы: 31

Бренд: Poulan Pro Страницы: 48

Бренд: Surtek Страницы: 17

Podadora 1302720

Бренд: Surtek Страницы: 8

Бренд: Husqvarna Страницы: 44

Бренд: Husqvarna Страницы: 48

Бренд: Husqvarna Страницы: 48

Бренд: Husqvarna Страницы: 60

Бренд: Husqvarna Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды