Jonsered FR 13 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 68

background image

English –

53

2

1

2B

3

4

4

6

2A

7

8

5

6012-081

8009-137

6012-082

Removing Blades with Bearings

WARNING!
Use gloves and protective
eyewear when working with the
cutting unit.

• Loosen the spring that tensions the V-belt (1) and

wriggle the belt off.

• Loosen the screw that holds the pulley (2) and

remove the pulley; you may need a puller for this.
Do not lose the key that sits between the pulley
and the axle.

Loosen the screw that holds the blades and remove
screws, washers, and blades.

Replacing the Shear Pin, Mulching Unit

The blades are fitted with a shear pin to protect the
mulching unit and its drive when colliding with
obstacles. A domed, spring friction washer is fitted
to each blade bolt. The washer must always be
replaced with a new washer when replacing the
shear pin. Otherwise the shear pin can break
causing the blades to collide.

Only use original spare parts. A set containing a
blade, shear pin, and friction washer can be
purchased from your dealer.

1. Put the unit in the service position, see Remov-

ing the Cutting unit.

2. Remove the blade (2A) by removing the blade

bolt with washer and friction washer (2B).

3. Remove the remains of the broken shear pin (3).

4. Make sure the contact surfaces (4) on the blade

and the blade mounting are metallically clean.
Clean if necessary.

5. Fit

a

new shear pin (5) in the blade mounting.

6. Fit the blade (6), make sure it is fitted as illus-

trated.

7. Fit a

new

friction washer (7) with the concave

face turned towards the blade.

8. Fit the blade bolt with washer (8). Tightening

torque 45-50 Nm (4.5-5 kpm)

Repair Instructions

«
...
53
54
55
56
57
...
»

Содержание FR 13





































































Отзывы:

Нет отзывов

Похожие инструкции для FR 13

Бренд: McCulloch Страницы: 36

Бренд: Lawn-Boy Страницы: 20

Бренд: Lawn-Boy Страницы: 16

ransomes hr3806

Бренд: Jacobsen Страницы: 172

Бренд: MTD Страницы: 16

Бренд: Yard Works Страницы: 35

Бренд: Etesia Страницы: 42

Бренд: Zenoah Страницы: 2

Бренд: Snapper Страницы: 4

Бренд: Villager Страницы: 128

Бренд: Exmark Страницы: 5

Бренд: Gardenline Страницы: 24

Бренд: Yardworks Страницы: 24

Бренд: Ariens Страницы: 26

Harmony HRB217TDA

Бренд: Honda Страницы: 76

Бренд: AL-KO Страницы: 20

Бренд: Eliet Страницы: 106

Бренд: Honda Страницы: 107

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды