Jonsered FR 13 Скачать руководство пользователя страница 10

Страница: 10 / 68

– English

Dealer Service

25-Hour Service

1. Change engine oil.

2. Clean/replace the air cleaner’s pre-filter or Oil-

foam element if fitted.
(Shorter intervals for dusty operating conditions.)

3. Clean/replace the air cleaner’s filter cartridge

(25 hours, 100 hours when a pre-filter is in
place).
(Shorter intervals for dusty operating conditions.)

3. Check the tyre pressures.

4. Check the cutting unit (visual inspection).

5. Lubricate the belt adjuster.

6. Lubricate joints and shafts.

7. Adjust the brake (FR 13, FR 2111).

8. Check the V-belts.

9. Clean the engine’s cooling air intake.

10. Check/clean the hydrostatic transmission’s

cooling fins.

50-Hour Service

1. Perform the 25-hour service as detailed above.

2. Check the transmission oil level

(Hydrostatic machines).

3. Check/adjust the parking brake

(Hydrostatic machines).

4. Check/adjust the throttle cable.

5. Clean the engine and transmission cooling fins.

6. Check/adjust the cutting unit settings.

7. Inspect the flame proofing/spark extinguisher

(extra equipment)

100-Hour Service

1. Perform the 25-hour service as detailed above.

2. Perform the 50-hour service as detailed above.

3. Replace the air cleaner’s pre-filter and paper

filter.

4. Change the inline fuel filter.

5. Clean/replace the spark plug.

Delivery and Dealer Service

300-Hour Service

1. Inspect the machine. Reach agreement with the

customer with regard to what additional work is
to be carried out.

2. Perform the 25-hour service as detailed above.

3. Perform the 50-hour service as detailed above.

4. Perform the 100-hour service as detailed

above.

5. Check the play in the engine valves.

At Least Once Each Season

1. Change the engine oil (25 hours).

2. Clean/replace the air cleaner’s pre-filter or Oil-

foam element if fitted.

3. Clean/replace the air cleaner’s filter cartridge.

4. Check/adjust the cutting unit settings.

5. Adjust the parking brake.

6. Inspect the flame proofing/spark extinguisher,

extra equipment.

7. Clean/replace the spark plugs.

8. Change the inline fuel filter.

9. Clean the engine and transmission cooling fins.

10. Check the play in the engine valves.

11. Perform the 300-hour service at an authorised

service workshop.

Содержание FR 13





































































Результаты поиска

Содержание FR 13

Отзывы:

Похожие инструкции для FR 13

Бренды по названию

Популярные бренды

Jonsered FR 13, Руководство по ремонту

Результаты поиска

Содержание FR 13

Отзывы:

Похожие инструкции для FR 13

Бренды по названию

Популярные бренды