Jonsered FR 13 Скачать руководство пользователя страница 36

Страница: 36 / 68

– English

6012-098

6012-093

6012-094

8009-211

Repair Instructions

• Lubricate half the shaft (the half that has not

been lathed) and press it into the steering
spindle from the rear (see illustration).

• Fit the washer and circlip on the pendulum shaft

by the inner mount.

• Fit the dust cover (with thin lip towards the rear)

approx. 2/3 of the way in on the shaft and lubri-
cate the shaft on both sides of the dust cover.

Fitting the Pendulum Shaft

Roll the rear frame forward and press it onto the
pendulum shaft.

• Fit the washer and circlip on the pendulum shaft.

• Fit the hydrostatic transmission cable and its

casing (2+4).

• Attach the cable to the neutral position contact

(5).

• Fit the rear belt (8).

• Attach the brake cable to the arm under the tank

and the casing fixture on the rear frame (6).

• Fit the idler’s spring (1).

• Fit the hydrostatic transmission’s fan and the

circlip (7).

3 FR 13, FR 2111

• Fit the washer and circlip on the pendulum shaft

(1).

• Attach the cables’ mounting plates (2) and the

gear and brake cables (3 and 4).

• Wiggle the belt onto the pulley and screw the

idler’s arm (5) onto the rear frame.

• Attach the clutch cable (6) and the idler’s spring

(7).

Make sure that the cables and controls are properly
adjusted (see Checking and Adjusting the respec-
tive cables). Finally, fit the transmission/gearbox
cover.

Check the neutral position contact’s setting on
machines with hydrostatic transmission.

3 Hydrostatic Machines

Содержание FR 13





































































Результаты поиска

Содержание FR 13

Отзывы:

Похожие инструкции для FR 13

Бренды по названию

Популярные бренды

Jonsered FR 13, Руководство по ремонту

Результаты поиска

Содержание FR 13

Отзывы:

Похожие инструкции для FR 13

Бренды по названию

Популярные бренды