Jonsered FR 13 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 68

background image

28

– English

6019-005

Removing/Fitting the Cable Pulleys

1

Remove the frame plate.

2

Loosen the steering cables’ rear fixture (1).

3

Remove the screw (2) and remove the cable pulley
(5).

4

Remove the bearing’s circlip (3) and tap out the
bearing (4).

5

To assemble the cable pulley, follow the instructions
in the reverse order.

The screw (2) is to be mounted in the rear hole on
the frame. The bushing (6) is to be placed between
the frame and the cable pulley.

Repair Instructions

Ensure that the cables are properly situated under
the steering cable pulleys (7) in the frame tunnel.
Ensure that the steering wheel is in the centre
position when the rear wheels are centred. Re-set
the chain on the steering column’s sprocket or
adjust the rear fixture (1) for the steering cables (1)
as needed.

Hold the cables with, for example, a wrench when
mounting so that they do not twist.

After mounting, the cable tension should be
checked (see Checking and Adjusting the Steering
Cables).

«
...
28
29
30
31
32
...
»

Содержание FR 13





































































Отзывы:

Нет отзывов

Похожие инструкции для FR 13

Бренд: Sabre Страницы: 9

Бренд: Zipper Mowers Страницы: 28

Бренд: MTD Страницы: 16

911394 - Pro 21SCH

Бренд: Gravely Страницы: 23

Бренд: Barbieri Страницы: 2

Бренд: FGM Страницы: 33

Бренд: Alamo Industrial Страницы: 186

EcoCut 135 Z-042

Бренд: Talex Страницы: 164

Poulan Pro 961140016

Бренд: Poulan Pro Страницы: 2

Бренд: Electrolux Страницы: 13

Бренд: Electrolux Страницы: 16

Бренд: Electrolux Страницы: 12

Бренд: Electrolux Страницы: 35

Бренд: Electrolux Страницы: 9

Бренд: Electrolux Страницы: 61

Бренд: Electrolux Страницы: 84

Бренд: Electrolux Страницы: 10

Бренд: ARNETOLI MOTOR Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды