Jonsered FR 13 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 68

background image

2

– English

Safety Instructions

General Instructions

This workshop manual has been written for person-
nel with general knowledge about repairing and
servicing riders.

The workshop where rider repairs are to be done
must be equipped with safety equipment in accord-
ance with local legislation.

No one may repair the rider unless they have read
and understood the content of this workshop
manual.

The machine is tested and approved only with the
equipment originally provided or recommended by
the manufacturer.

This workshop manual contains the following boxes
in relevant places.

IMPORTANT INFORMATION

This box warns of material damage if the
instructions are not followed.

Special Instructions

The fuel used in the rider has the following hazard-
ous properties:

• The fluid and its vapour are poisonous.

• Can cause eye and skin irritation.

• Can cause breathing problems.

• Is highly flammable.

When using compressed air, do not direct the jet
towards your body. Air can penetrate into the blood
circulation, which entails mortal danger.

Wear earmuffs/earplugs when test running.

After test running, do not touch the muffler until it
has cooled. Risk for burns. This applies especially if
the rider is fitted with a catalyser. The coatings on
the inside and outside of the catalyser element are
harmful if ingested. Used protective gloves when
working with the catalyser/muffler.

The blades are sharp and can cause cuts and
gashes. Used protective gloves when handling the
blades.

Use eye protection when working with the cutting
unit. If the belt’s tension spring breaks off and flies
out, it can cause personal injury.

Be especially careful when handling battery acid.
Acid on the skin can cause serious corrosive
injuries. If you should get acid on your skin, rinse
immediately with water.
Acid in the eyes can cause blindness, contact a
doctor.

Be careful when servicing the battery. Explosive
gases form in the battery. Never perform mainten-
ance on the battery while smoking or in the vicinity
of open flames or sparks. This can cause the
battery to explode and cause serious injuries.

WARNING!
The warning box warns of the
risk of personal injury if the
instructions are not followed.

IMPORTANT INFORMATION

Waste oil and used oil filters shall be
managed as environmentally damaging
waste.

«
...
2
3
4
5
6
...
»

Содержание FR 13





































































Отзывы:

Нет отзывов

Похожие инструкции для FR 13

Бренд: ECLOZ Страницы: 56

Бренд: Land Pride Страницы: 2

Бренд: Walker Страницы: 84

ZERO TURN MOWERS

Бренд: Bush Hog Страницы: 30

Бренд: Yazoo/Kees Страницы: 34

Бренд: VITO GARDEN Страницы: 64

Бренд: Cub Cadet Страницы: 76

Бренд: Craftsman Страницы: 8

Бренд: Craftsman Страницы: 20

Бренд: Craftsman Страницы: 20

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 12

Бренд: Craftsman Страницы: 20

Бренд: Craftsman Страницы: 8

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды