Jonsered FR 13 Скачать руководство пользователя страница 64

Страница: 64 / 68

Engine fault

Transmission fault

Engine speed falling

Drive belt for transmission shaft

Transmission overheated

Oil level too low

The machine slows down
under heavy loads

The drive belt

The hydrostatic transmission’s
cooling fan

Belt wheel on the hydrostatic
transmission’s ingoing shaft

Hydrostatic transmission

Bypass valve

The valve’s needle wrongly
placed

Check the belt tensioning
device

Belt worn

Fan blades damaged or moving
against foreign objects

The wheel is loose or damaged

Oil level too low

Oil filter blocked

Noise from transmission

Repair the engine

Belt worn or oily
Clean or replace belt

Adjust belt tension

Stop and allow the transmission
to cool. Clean the cooling fins

Fill with engine oil SAE 10W/30
to right level

Repair

Lubricate bearing or replace belt
tensioning device

Replace belt

Clean or replace fan

Fill with engine oil SAE 10W/30
to right level

Tighten or replace belt wheel

Replace oil filter

The hydrostatic transmission must not be opened while under guarantee.

Содержание FR 13





































































Результаты поиска

Содержание FR 13

Отзывы:

Похожие инструкции для FR 13

Бренды по названию

Популярные бренды

Jonsered FR 13, Руководство по ремонту

Результаты поиска

Содержание FR 13

Отзывы:

Похожие инструкции для FR 13

Бренды по названию

Популярные бренды