Jonsered FR 13 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 68

background image

32

– English

4

3

8009-215

6012-027

6012-026

6012-028

6012-025

Repair Instructions

Loosen the centre spring. This spring is under high
tension and should be secured with the help of tool
number 506 89 93-01 before the nut is removed.

• Force the belts off of the pulley (2).

• Loosen the steering cables (1) and remove the

steering collar.

• Remove the pulley (B). Move the lower part

forwards, the upper part backwards, and force
the pulley out.

WARNING!
The centre spring is under
extremely high tension and can
cause injuries if it flies off. Wear
protective eyewear and gloves
when removing or fitting the
spring.

6

5

Remove the inner catch circlip (1) by the lower
bearing (see illustration). The rear carriage is now
loose and can be moved. Then loosen the outer
circlip (2) and remove the bearings from below.

• Remove the upper bearings from above, if they

are stuck tap them from below.

• Fit the new bearings and the articulated steering

in the reverse order that the old bearings were
removed.

• After mounting, the cable tension should be

checked (see Checking and Adjusting the
Steering Cables). Check that the controls and
cables are properly adjusted.

• Check the neutral position contact’s setting on

machines with a hydrostatic transmission.

«
...
32
33
34
35
36
...
»

Содержание FR 13





































































Отзывы:

Нет отзывов

Похожие инструкции для FR 13

Бренд: Kärcher Страницы: 32

Бренд: Cub Cadet Страницы: 32

Бренд: Gardenline Страницы: 28

Бренд: Snapper Страницы: 20

Бренд: BOXER AGRI Страницы: 15

Бренд: Qualcast Страницы: 16

Бренд: Bad Boy Страницы: 36

Бренд: ECLOZ Страницы: 56

Бренд: VITO GARDEN Страницы: 64

Бренд: MTD Страницы: 32

Бренд: Husqvarna Страницы: 56

Бренд: Scag Power Equipment Страницы: 30

Бренд: Mountfield Страницы: 20

Бренд: Mountfield Страницы: 14

Бренд: Craftsman Страницы: 28

Бренд: Craftsman Страницы: 30

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды