Jonsered FR 13 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 68

background image

English –

29

1

1

2

6012-016

6012-015

6008-239H

Repair Instructions

Checking and Adjusting the Brake Cable

FR 13, FR 2111

Make sure that the brakes are properly adjusted by
measuring the distance between the brake lever
and the cut-out’s forward edge on the chassis.
The distance should be 0–1 mm with the brake off.

1

Loosen the lock nuts (1).

2

Tension the cable with the adjustment screw (2) so
that the distance between the brake lever and front
edge of the cut-out on the chassis is 1 mm.

3

Tighten the lock nuts (1) after adjustment. When the
brake cable is adjusted, you should make sure that
the brake lever does not have too much play. If the
range of movement of the lever arm exceeds 9 mm,
it should be adjusted by tightening the nut on the
brake lever arm.

1

Loosen the lock nuts (1).

2

Tension the cable using the adjuster screw (2) until
the play in the cable disappears.

3

Tighten the lock nuts (1).

4

The brakes should be checked again after the
adjustment has been made.

Hydrostatic Machines

Check that the brakes are correctly adjusted by
placing the rider on a slight downhill slope with the
clutch disengaged and activating the brake.
If the rider does not stand still the brake needs
adjusting.

WARNING!
A poorly adjusted brake can
result in reduced braking ability.

«
...
29
30
31
32
33
...
»

Содержание FR 13





































































Отзывы:

Нет отзывов

Похожие инструкции для FR 13

Бренд: Ybravo Страницы: 16

Бренд: McCulloch Страницы: 80

Бренд: MTD Страницы: 12

Бренд: MTD Страницы: 28

Бренд: Jacobsen Страницы: 50

Бренд: Ariens Страницы: 26

Бренд: Gtech Страницы: 32

Бренд: Honda Страницы: 24

Бренд: Baroness Страницы: 36

Бренд: Yazoo/Kees Страницы: 34

Recycler 119-3320

Бренд: Toro Страницы: 4

Бренд: Toro Страницы: 24

Бренд: Ikra Страницы: 56

Бренд: Husqvarna Страницы: 37

Бренд: Husqvarna Страницы: 36

Бренд: Husqvarna Страницы: 40

Бренд: Husqvarna Страницы: 32

Бренд: Husqvarna Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды