Joab EcoDrive LA Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 89

background image

Icon

Description

Icon

Description

Slush flap*

Salt spreader*

Float mode - Plough

LS Salt spreader*

Automatic Plough UP on reverse

Sand spreader*

Plough work lights*

--

--

Table 8: Icon Definitions APC

* Option

Float Mode

The front plough can be set to float mode if desired, by pressing the following icon

. Float

mode is normally used to plough roads. It allows the plough to move up and down so that is fol-
lows the road's form. There are three states for this function, which are displayed by a green
status bar above the icon. The three states: off, flashing, and on, are described below.

1.

OFF

- float function is not active.

2.

Flashing

- the float valve is disengaged but will engage when the control-stick is pushed

forwards.

3.

ON

- the float valve is engaged and the plough is in float mode.

To activate float mode, first press the float icon

. The green status bar above it will then

flash. Then push the control-stick forwards to lower the front plough. Float mode will then be
engaged and will remain engaged until either the front plough is raised or the float mode button
is pressed.

The side plough is by default set to work in float mode. However, if desired, it can be raised to a
desired height and it will remain at that position. Float mode is deactivated as soon as it is
raised.

Automatic Plough UP on Reverse

The snow ploughs can also be set to automatically lift up whenever the vehicle is put into
reverse gear. This function is activated by pressing the following icon

. The front plough is

raised while the side plough is retracted and raised.

The duration and rate of hydraulic flow for the automatic plough up function is set at factory,
however, it can be calibrated if required. This must be done by a JOAB technician.

29

Operation | EcoDriveOptional Functions

EcoDrive 2.0 manual: 1021970 Edition 1 | 2022-02-04

«
...
35
36
37
38
39
...
»

Содержание EcoDrive LA


























































































Отзывы:

Нет отзывов

Похожие инструкции для EcoDrive LA

Бренд: ICP DAS USA Страницы: 5

Бренд: ICP DAS USA Страницы: 7

Бренд: Panamax Страницы: 16

Бренд: BlitzRotary Страницы: 41

MorphoAccess VP MD

Бренд: Idemia Страницы: 29

Бренд: Reflex Страницы: 26

Бренд: Contec Страницы: 7

Бренд: Hanshen Страницы: 18

Бренд: M-system Страницы: 7

Бренд: Valx Страницы: 28

STRATA_HEAT 120V

Бренд: LATICRETE Страницы: 12

Бренд: M-system Страницы: 3

Бренд: M-system Страницы: 5

Бренд: Nußbaum Hebetechnik Страницы: 32

Liftkar SAL Uni

Бренд: SANO Страницы: 24

Бренд: M-system Страницы: 7

Бренд: Longevity Страницы: 25

Бренд: GYS Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды