Joab EcoDrive LA Скачать руководство пользователя страница 59

Страница: 59 / 89

Unloading a Body

The operator of the hook-lift is responsible for handling it. Care must be taken to
avoid injury or damage. Before operating the hook-lift make sure that you have read
and are fully aware of the warnings in this manual and on the hook-lift.

Before unloading a body, refer to and read

"Distributing a Load on a Body", on page 41

. To

unload a body, follow the procedure listed below:

Make sure that there is nobody within the working area of the vehicle and the body.

If the vehicle is fitted with an extendable underrun - retract it. Refer to

"Extendable Under-

run Protection", on page 32

Start the hydraulic pump. Once the pump
is started, the pump icon will be displayed
in the CBW controller as shown.

For information regarding the starting of
the pump, refer to

"User Interface", on

page 12

Open the hydraulic lock. Once open, the
hydraulic-lock-open icon is displayed in
the CBW controller.

EcoDrive 2.0 manual: 1021970 Edition 1 | 2022-02-04

Содержание EcoDrive LA


























































































Результаты поиска

Содержание EcoDrive LA

Отзывы:

Похожие инструкции для EcoDrive LA

Бренды по названию

Популярные бренды

Joab EcoDrive LA, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание EcoDrive LA

Отзывы:

Похожие инструкции для EcoDrive LA

Бренды по названию

Популярные бренды