Joab EcoDrive LA Скачать руководство пользователя страница 22

Страница: 22 / 89

Icon

Function

Icon

Function

Spreader flap - VEHICLE*

Axle lift - TRAILER*

The hooklift is in its lowered
status.

Position memory system*

Retract the underrun protection

Extend the underrun protection

Turtle mode - used for heavy or
delicate loads.

Table 2: User interface – icon description (continued)

*Extra option. Not standard equipment. **LA models only.

NOTE

: The above functions:

Automatic flap - VEHICLE

and

Automatic flap - TRAILER

can be

operated without the hydraulic pump being turned ON. Simply keep the icon pressed for 10
seconds to activate them without turning the pump on.

NOTE

: FFD must be

de-activated

when working with bodies that have dowel pins that are

used to anchor the body onto the vehicle. If FFD is active, damage can occur. See

"Friction

Free Drive - FFD", on page 23

for further information.

NOTE

: This only applies to JOAB equipment installed on the hooklift. It does not apply to

equipment installed by the manufacturer of the vehicle.

NOTE

For Scania vehicles, this can also be activated automatically when the vehicle is put

into reverse. To do this, press the load light button on the drivers door for 5 seconds.

Page Setups

The user interface can display one of five main page setups, each configured with user defined
functions. In addition, a page that displays information regarding the position of the hook on the
hooklift can also be displayed. See

"Hook Positioning", on page 15

below. The pages available

are listed below. The page setup that is active is displayed in the bottom right-hand side of the
screen with one of the following icons (see

"User Interface", on page 12

Icon

Description

Icon

Description

Vehicle setup_1

Lighting setup

Vehicle setup_2

Snow plough setup

Table 3: Page setups

Operation | CBW controller

EcoDrive 2.0 manual: 1021970 Edition 1 | 2022-02-04

Содержание EcoDrive LA


























































































Результаты поиска

Содержание EcoDrive LA

Отзывы:

Похожие инструкции для EcoDrive LA

Бренды по названию

Популярные бренды

Joab EcoDrive LA, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание EcoDrive LA

Отзывы:

Похожие инструкции для EcoDrive LA

Бренды по названию

Популярные бренды