Joab EcoDrive LA Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 89

background image

The first menu option, shown above, provides statistical information regarding the use
of the hooklift.

The second menu provides information regarding the version of software installed and
hooklift model.

The third menu option provides diagnostic information regarding sensors and input sig-
nal status for the hooklift.

The fourth menu option provides information regarding outputs from the master mod-
ule.

The fifth menu option provides an emergency operation mode and the option to cal-
ibrate the hooklift. For further information about the emergency operation refer to

"Emergency Operation", on page 20

Emergency Stop

In case of an emergency, such as a hydraulic leak or risk of injury, an emergency stop button is
fitted to the CBW controller (see

"CBW controller", on page 11

). Pressing the emergency stop

button will stop all functions of the hooklift immediately. To reset the emergency stop function,
turn the pump off, reset the emergency stop button, and then restart the pump.

Emergency Operation

Caution must be taken when using the emergency operating system. The hook-lift's
safety system is disengaged. There is a risk of damage to the hook-lift or injury if due
care is not taken. Before using the emergency override make sure that you are fully
aware of its operation.

It is possible to operate the hook-lift even though the hydraulic-lock is closed. Oper-
ating the hook-lift when the hydraulic-lock is closed can cause damage to the body.
Make sure to unlock the hydraulic-lock first, before performing: load, unload, and
shunting operations. The lock must be closed for tipping operations.

In the event of a failure in the hook-lift’s system, it is possible to still operate the hook-lift using
the emergency system. To activate the emergency system, follow the procedure listed below:

If in any doubt about the use of the emergency override, contact JOAB for advice before using
it.

20

Operation | CBW controller

EcoDrive 2.0 manual: 1021970 Edition 1 | 2022-02-04

«
...
26
27
28
29
30
...
»

Содержание EcoDrive LA


























































































Отзывы:

Нет отзывов

Похожие инструкции для EcoDrive LA

Бренд: Parkside Страницы: 54

Бренд: Ravaglioli Страницы: 72

Бренд: Estun Страницы: 41

PRECISION TIG 185

Бренд: Lincoln Electric Страницы: 104

Бренд: FUHR Страницы: 20

Бренд: R. Beck Maschinenbau Страницы: 36

Бренд: National Instruments Страницы: 9

Бренд: iWeld Страницы: 10

CompactModule CR2032

Бренд: IFM Страницы: 29

Бренд: Yeswelder Страницы: 8

Weighing System

Бренд: NAUSICAA Страницы: 16

Бренд: Omron Страницы: 154

Бренд: Sunrise Medical Страницы: 36

Бренд: M-system Страницы: 10

Бренд: National Instruments Страницы: 28

Бренд: Century Страницы: 27

Automower Connec

Бренд: Husqvarna Страницы: 80

LiftRunner B frames

Бренд: Still Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды