JLG GRADALL 544D-10 Скачать руководство пользователя страница 55

Страница: 55 / 142

Section 4 - Operation

4-5

31200172

4.2

OPERATING WITH A NON-SUSPENDED LOAD

Lift Load Safely

• You must know the weight and load center of every load you lift. If you are not

sure of the weight and load center, check with your supervisor or with the
supplier of the material.

• Know the rated load capacities (see Section 5) of the telehandler to determine

the operating range in which you can safely lift, transport and place a load.

Picking Up a Load

• Note the conditions of the terrain. Adjust travel speed and reduce amount of load

if conditions warrant.

• Avoid lifting double-tiered loads.

• Make sure load is clear of any adjacent obstacles.

• Adjust spacing of forks so they engage the pallet or load at maximum width. See

“Adjusting/Moving Forks”

on page 5-15.

• Approach load slowly and squarely with fork tips straight and level.

NEVER

attempt to lift a load with just one fork.

•

NEVER

operate telehandler without a proper and legible capacity chart in the

operator cab for the telehandler/attachment combination you are using.

WARNING

TIP OVER HAZARD.

Exceeding lift capacity of the telehandler could damage the

equipment and/or cause tip over.

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Бренды по названию

Популярные бренды