JLG GRADALL 544D-10 Скачать руководство пользователя

Страница: 87 / 142

Section 5 - Attachments

5-25

31200172

The joystick (

) controls lift/lower and extend/retract movement of the boom.

The tilt lever (

) controls the mast tilt.

• Move lever back to tilt up.

• Move lever forward to tilt down.

To Raise/Lower Mast:

The auxiliary hydraulic lever (

) controls the raise/lower movement of the mast.

• Move lever up to lower.

• Move lever down to raise.

Installation Procedure:

Refer to

“Attachment Installation”

on page 5-11.

Operation:

• Always lower forks fully in mast before engaging load.

• To drive with a load, lower forks fully in mast and travel in accordance with the

requirements set forth in Section 1 - General Safety Practices.

• Use a signal person to assist in positioning of load if necessary.

Equipment Damage Precautions:

• Do not use forks as a lever to pry material. Excessive prying forces could

damage forks or machine structure.

• Do not attempt to lift loads that are attached or connected to another object.

WARNING

CRUSH HAZARD.

Do not use mast to push or pull objects or load. Failure to

comply could cause object or load to fall.

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды