JLG GRADALL 544D-10 Скачать руководство пользователя

Страница: 83 / 142

Section 5 - Attachments

5-21

31200172

The joystick (

) controls lift/lower and extend/retract movement of the boom.

The tilt lever (

) controls the carriage tilt.

• Move lever back to tilt up.

• Move lever forward to tilt down.

To Side Tilt:

The auxiliary hydraulic lever (

) controls the carriage side tilt.

• Move lever up to (side) tilt left.

• Move lever down to (side) tilt right.

Installation Procedure:

• Refer to

“Attachment Installation”

on page 5-11.

Operation:

• Approach load with forks centered on load and stop telehandler.

• Level telehandler before side tilting carriage to engage load.

• Side tilt carriage to left or right to align forks with load and engage load.

• Raise load slightly and level carriage side to side.

• Travel in accordance with the requirements set forth in Section 1 - General

Safety Practices.

Equipment Damage Precautions:

• Do not use forks as a lever to pry material. Excessive prying forces could

damage forks or machine structure.

• Do not attempt to lift loads that are attached or connected to another object.

WARNING

CRUSH HAZARD.

Do not use side tilt to push or pull objects or load. Failure to

comply could cause object or load to fall.

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды