JLG GRADALL 544D-10 Скачать руководство пользователя

Страница: 62 / 142

Section 4 - Operation

4-12

31200172

Lifting

• When lifting machine, it is very important that the lifting device and equipment is

attached only to designated lifting points. If machine is not equipped with lifting
lugs contact JLG Product Safety for information.

• Make adjustments to the lifting device and equipment to ensure the machine will

be level when elevated. The machine must remain level at all times while being
lifted.

• Ensure that the lifting device and equipment is adequately rated and suitable for

the intended purpose. See Section 9 - Specifications for machine weight.

• Remove all loose items from machine prior to lifting.

• Lift machine with smooth, even motion. Set machine down gently. Avoid quick or

sudden motions that could cause shock loads to machine and/or lifting devices.

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды