JLG GRADALL 544D-10 Скачать руководство пользователя

Страница: 43 / 142

Section 3 - Controls and Indicators

3-9

31200172

Right Hand Levers (if equipped)

The right hand levers control attachment tilt, frame level or auxiliary hydraulics.

Attachment Tilt (if equipped)

The attachment tilt lever (

) controls attachment tilt.

• Move lever forward to tilt down; move lever back to tilt up.

Frame Level (if equipped)

The frame level lever (

) controls the left to right frame level.

• Move lever forward to rotate frame left, move lever back to rotate frame right.

• A level indicator is located above the front cab window to permit operator to

determine whether the telehandler frame is level.

Auxiliary Hydraulics (if equipped)

• The auxiliary hydraulics lever (

) controls function of attachments that require

hydraulic supply for operation. See Section 5 - Attachments for approved
attachments and control instructions.

WARNING

TIP OVER HAZARD.

Always move boom as low as possible while allowing for

best visibility of right hand mirror before leveling frame. Attempting to level
machine with boom raised could cause it to tip over.

OX0660

ATTACHMENT

TILT

FRAME

LEVEL

AUXILIARY

HYDRAULICS

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды