JLG GRADALL 544D-10 Скачать руководство пользователя

Страница: 110 / 142

Section 7 - Lubrication and Maintenance

7-2

31200172

7.2

GENERAL MAINTENANCE INSTRUCTIONS

Prior to performing any service or maintenance on the telehandler, follow the
shut-down procedure on page 4-4 unless otherwise instructed. Ensure
telehandler is level, for proper fluid readings.

• Clean lubrication fittings before lubricating.

• After greasing telehandler, cycle all functions several times to distribute

lubricants. Perform this maintenance procedure without attachment installed.

• Apply a light coating of engine oil to all linkage pivot points.

• Intervals shown are for normal usage and conditions. Adjust intervals for

abnormal usage and conditions.

• Drain engine and gear cases after operating when oil is hot.

• Check all lubricant levels when lubricant is cool. For ease of filling hydraulic

reservoir, use a funnel with a hose or flexible tube for best results.

Note:

Be certain to check boom chain adjustment every 500 hours and adjust as

required. Chain damage can occur if chain is not adjusted properly.

WARNING

CUT/CRUSH/BURN HAZARD.

Do not perform service or maintenance on the

machine with the engine running, with the exception of the hydraulic return filter
indicator checks.

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды