JLG GRADALL 544D-10 Скачать руководство пользователя

Страница: 94 / 142

Section 5 - Attachments

5-32

31200172

Fork Mounted Hook (S/N 0160037689 & After)

Description

P/N

Fork Mounted Hook ...................................................... 91565094

Use Fork Mounted Hook Attachment Capacity Chart

To determine maximum capacity, refer to

“Telehandler/Attachment/Fork Capacity”

page 5-3.

Suspend loads in accordance with requirements set forth in Section
1 - General Safety Practices.

The joystick (

) controls lift/lower and extend/retract movement of the boom.

The tilt lever (

) controls the fork mounted hook tilt.

• Move lever back to tilt up.

• Move lever forward to tilt down.

Installation Procedure:

• Refer to

“Attachment Installation”

on page 5-11.

• Secure the fork mounted hook to the forks by sliding the fork mounted hook onto

the parent forks and install the retaining pin behind the vertical shank of the fork.

OY0640

OX0261

2-FRONT

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды