JLG GRADALL 544D-10 Скачать руководство пользователя страница 74

Страница: 74 / 142

Section 5 - Attachments

5-12

31200172

Before S/N 0160037689

This installation procedure is designed for one-person operation. Prior to exiting cab,
perform

“Shut-Down Procedure”

on page 4-4.

1. Tilt quick switch back to provide clearance. Check

to be sure lock pin is secured in out position with
retainer pin.

2. Align attachment pin with recess in attachment.

Raise boom slightly to engage attachment pin in
recess.

3. Tilt quick switch forward to engage attachment.

4. Remove retainer pin and slide lock pin in fully.

Secure lock pin in locked position using retainer
pin.

5. If equipped, swing attachment saddles down and

pin in place.

6. If equipped, connect auxiliary hydraulic hoses. See

“Hydraulic Operated

Attachment”

on page 5-14.

7. If equipped, connect auxiliary electric harness.

OX0690

OX0700

OX0710

OX0720

OY0601

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Бренды по названию

Популярные бренды