manualshive.com logo in svg

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Поделиться
Скачать
JLG GRADALL 544D-10 Скачать руководство пользователя страница 108

Section 6 - Emergency Procedures

6-2

31200172

6.2

EMERGENCY LOWERING OF BOOM

In the event of total loss of engine power or hydraulic pump failure with an elevated
load, the situation must be properly evaluated and dealt with on an individual basis.

Contact a local Authorized Distributor for specific instructions.

Secure the telehandler using the following procedures:

1. Clear the area around telehandler of all personnel.

2. Engage the parking brake. Place the transmission control lever in “NEUTRAL”.

3. Block all four wheels.

4. Section off a large area under the boom with string or tape to restrict any 

personnel from entering this area.

6.3

EMERGENCY EXIT FROM ENCLOSED CAB

• In an emergency, pull pins at bottom of front window and push window out to exit.

OX0500

EMERGENCY

EXIT

PULL PINS AND PUSH

WINDOW OUT TO EXIT

D21080

Содержание GRADALL 544D-10















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды