JLG GRADALL 544D-10 Скачать руководство пользователя

Страница: 104 / 142

Section 5 - Attachments

5-42

31200172

Personnel Work Platform (S/N 0160037689 & After)

Description

P/N

Personnel Work Platform, ANSI................................ 1001103637
Personnel Work Platform, ANSI (French) ................. 1001103736
Personnel Work Platform, ISO.................................. 1001103730

Use Personnel Work Platform Capacity Chart

To determine maximum capacity, refer to

“Telehandler/Attachment/Fork Capacity”

page 5-3.

The operator and personnel in platform must read and understand the
separate personnel work platform manual prior to installing and using a
platform.

The joystick (

) controls lift/lower and extend/retract movement of the boom.

The tilt lever (

) controls platform tilt.

• Move lever back to tilt up.

• Move lever forward to tilt down.

Installation Procedure:

• Refer to

“Attachment Installation”

on page 5-11.

• Check to ensure the personnel platform is securely attached to the forks and/or

carriage.

OY1610

OX0770

2-FRONT

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды