JLG GRADALL 544D-10 Скачать руководство пользователя

Страница: 64 / 142

Section 5 - Attachments

5-2

31200172

5.2

UNAPPROVED ATTACHMENTS

Do not use unapproved attachments for the following reasons:

• Range and capacity limitations for “will fit,” homemade, altered, or other

non-approved attachments cannot be established.

• An overextended or overloaded telehandler can tip over with little or no warning

and cause serious injury or death to the operator and/or those working nearby.

• The ability of a non-approved attachment to perform its intended function safely

cannot be assured.

WARNING

Use only approved attachments. Attachments which have not been approved for
use with your telehandler could cause machine damage or an accident.

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды