JLG GRADALL 544D-10 Скачать руководство пользователя

Страница: 11 / 142

Section 1 - General Safety Practices

1-1

31200172

SECTION 1 - GENERAL SAFETY PRACTICES

1.1

HAZARD CLASSIFICATION SYSTEM

Safety Alert System and Safety Signal Words

DANGER

indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

indicates a potentiality hazardous situation which, if not avoided, may

result in minor or moderate injury.

1.2

GENERAL PRECAUTIONS

WARNING

Before operation, read and understand this manual. Failure to comply with the
safety precautions listed in this manual could result in machine damage, property
damage, personal injury or death.

DANGER

OW0010

WARNING

OW0021

CAUTION

OW0031

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды