JLG GRADALL 544D-10 Скачать руководство пользователя

Страница: 85 / 142

Section 5 - Attachments

5-23

31200172

The joystick (

) controls lift/lower and extend/retract movement of the boom.

The tilt lever (

) controls the carriage tilt.

• Move lever back to tilt up.

• Move lever forward to tilt down.

To Swing:

The auxiliary hydraulic lever (

) controls the carriage swing.

• Move lever up to swing left.

• Move lever down to swing right.

Installation Procedure:

• Refer to

“Attachment Installation”

on page 5-11.

Operation:

• To drive with a load, keep forks pointed forward and travel in accordance with the

requirements set forth in Section 1 - General Safety Practices.

Equipment Damage Precautions:

• Do not use forks as a lever to pry material. Excessive prying forces could

damage forks or machine structure.

• Do not attempt to lift loads that are attached or connected to another object.

WARNING

CRUSH HAZARD.

Always level forks (horizontally) and telehandler frame before

swinging load to side. Swinging unlevel forks could cause load to slide off forks.

WARNING

CRUSH HAZARD.

Do not use swing carriage to push or pull objects or load.

Failure to comply could cause object or load to fall.

WARNING

CRUSH HAZARD

. Use retaining pin (if equipped) for locking swing frame to fixed

frame when carrying loads greater than 5000 lb. Failure to comply could cause
object or load to fall.

Содержание GRADALL 544D-10















































































































































Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды

JLG GRADALL 544D-10, Инструкция по эксплуатации и безопасности

Результаты поиска

Содержание GRADALL 544D-10

Отзывы:

Похожие инструкции для GRADALL 544D-10

Бренды по названию

Популярные бренды